Description

Fitment: 2008-2012 Ford Escape 2009-2011 Mercury Mariner Notes: The radiator cooling fan is an integral part of your car that is responsible for cooling the radiator of your car. The radiator cooling fan does this by either pulling or pushing air into the radiator keeping the radiator temperatures within the safe levels. A damaged radiator cooling fan is a determining factor in preventing your car from overheating. Below are the materials that you need along with the instructions on how to replace a radiator cooling fan. Step 1: Locate the Radiator Cooling Fan Radiator and Cooling Fan Assembly Kit For 2008 2009 2010 2011-2012 Ford Escape Fitment: 2008-2012 Ford Escape 2009-2011 Mercury Mariner Notes: The radiator cooling fan is an integral part of your car that is responsible for cooling the radiator of your car. The radiator cooling fan does this by either pulling or pushing air into the radiator keeping the radiator temperatures within the safe levels. A damaged radiator cooling fan is a determining factor in preventing your car from overheating. Below are the materials that you need along with the instructions on how to replace a radiator cooling fan. Step 1: Locate the Radiator Cooling Fan Locating the radiator cooling fan is the first step in replacing it. Turn off your car and allow it to cool off. Open the hood of your car and you will be able to see the radiator that is located at the back of the grill at the front portion of your engine compartment. The radiator cooling fan is attached at the back of the radiator through a mounting frame. Under the engine and the radiator is a sticking cylinder that is encased in a small casing. That is the radiator cooling fan motor that you may need to change or repair other than the radiator cooling fan itself. Step 2: Disconnect the Power Supply On the fan motor is an electric cable running towards the engine. Find the connector of the wires from your engine and from your radiator fan motor and disconnect it. Using two masking tapes with different colors, note the connection of the wires so that you will not have a hard time reconnecting the wires later. Step 3: Remove the Fan Housing Using a crescent wrench, remove the four screws located at each corner of the fan housing. Remove the fasteners at the sides of the fan housing as well. A radiator cooling fan housing is relatively large and you may need to remove all the obstructions like hoses and wirings so that you can extract the fan housing off your car hood. Hold the housing firmly and lift it off your engine compartment. Be careful in removing the fan housing to avoid damaging it. Place the fan housing on a clutter-free working table. Step 4: Remove the Radiator Cooling Fan and the Fan Motor The fan blade is either pinned or screwed to a shaft. With a screwdriver, loosen the fan blade and slide if off its shaft. You may need to remove a keeper that prevents the fan blades from moving up in the shaft up and down. As to the fan motor itself, remove it from the fan housing using a screwdriver. Step 5: Attach the Replacement Radiator Cooling Fan and Fan Motor Install the new fan motor into the fan housing. Slide your replacement radiator cooling fan into the shaft, insert the keeper and secure the new cooling fan and keeper into place. Return the fan housing back into its proper place and secure the screws and the fasteners. Reattach the hoses and wires you removed in step 3. Connect the fan motor into the car electrical system using the electrical tape guide you made in step 54. You just learned how to replace your radiator cooling fan as well as your radiator cooling fan motor. Information About AC Condenser 1.Such condensers typically also use a fan to force air through the heat sink and away from the tropics. Refrigeration principle of the general refrigerator The function of the compressor is to compress the steam with lower pressure into steam with higher pressure, so that the volume of the steam is reduced and the pressure is increased. 2.The compressor draws in the lower pressure working fluid vapor from the evaporator, causes the pressure to rise, and then sends it to the condenser, which is condensed into a higher pressure liquid in the condenser, and is throttled after the throttling valve becomes a pressure. After the low liquid is sent to the evaporator, it absorbs heat in the evaporator and evaporates to become a lower pressure steam, thereby completing the refrigeration cycle. Radiator and Cooling Fan Assembly Kit For 2008 2009 2010 2011-2012 Ford Escape Fitment: 2008-2012 Ford Escape 2009-2011 Mercury Mariner Notes: The radiator cooling fan is an integral part of your car that is responsible for cooling the radiator of your car. The radiator cooling fan does this by either pulling or pushing air into the radiator keeping the radiator temperatures within the safe levels. A damaged radiator cooling fan is a determining factor in preventing your car from overheating. Below are the materials that you need along with the instructions on how to replace a radiator cooling fan. Step 1: Locate the Radiator Cooling Fan Locating the radiator cooling fan is the first step in replacing it. Turn off your car and allow it to cool off. Open the hood of your car and you will be able to see the radiator that is located at the back of the grill at the front portion of your engine compartment. The radiator cooling fan is attached at the back of the radiator through a mounting frame. Under the engine and the radiator is a sticking cylinder that is encased in a small casing. That is the radiator cooling fan motor that you may need to change or repair other than the radiator cooling fan itself. Step 2: Disconnect the Power Supply On the fan motor is an electric cable running towards the engine. Find the connector of the wires from your engine and from your radiator fan motor and disconnect it. Using two masking tapes with different colors, note the connection of the wires so that you will not have a hard time reconnecting the wires later. Step 3: Remove the Fan Housing Using a crescent wrench, remove the four screws located at each corner of the fan housing. Remove the fasteners at the sides of the fan housing as well. A radiator cooling fan housing is relatively large and you may need to remove all the obstructions like hoses and wirings so that you can extract the fan housing off your car hood. Hold the housing firmly and lift it off your engine compartment. Be careful in removing the fan housing to avoid damaging it. Place the fan housing on a clutter-free working table. Step 4: Remove the Radiator Cooling Fan and the Fan Motor The fan blade is either pinned or screwed to a shaft. With a screwdriver, loosen the fan blade and slide if off its shaft. You may need to remove a keeper that prevents the fan blades from moving up in the shaft up and down. As to the fan motor itself, remove it from the fan housing using a screwdriver. Step 5: Attach the Replacement Radiator Cooling Fan and Fan Motor Install the new fan motor into the fan housing. Slide your replacement radiator cooling fan into the shaft, insert the keeper and secure the new cooling fan and keeper into place. Return the fan housing back into its proper place and secure the screws and the fasteners. Reattach the hoses and wires you removed in step 3. Connect the fan motor into the car electrical system using the electrical tape guide you made in step 54. You just learned how to replace your radiator cooling fan as well as your radiator cooling fan motor. Information About AC Condenser 1.Such condensers typically also use a fan to force air through the heat sink and away from the tropics. Refrigeration principle of the general refrigerator The function of the compressor is to compress the steam with lower pressure into steam with higher pressure, so that the volume of the steam is reduced and the pressure is increased. 2.The compressor draws in the lower pressure working fluid vapor from the evaporator, causes the pressure to rise, and then sends it to the condenser, which is condensed into a higher pressure liquid in the condenser, and is throttled after the throttling valve becomes a pressure. After the low liquid is sent to the evaporator, it absorbs heat in the evaporator and evaporates to become a lower pressure steam, thereby completing the refrigeration cycle. Item Specifics Condition New Package included 1X Radiator,1X Cooling Fan Interchange Part Number 1 Year Warranty Direct Replacement Fitment Type Radiator and Cooling Fan Type CB837596S01 Manufacturer Part Number SCITOO Brand Front Material Aluminum Shipping WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. 2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days. 3.Local pick up is not available. 4. International Buyers C Please Note: a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ] Payment 1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc.. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns 1.All of our brand new items come with a 60-Days money-back guarantee. 2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding. 3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. 4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. 5.Shipping& handling cost are not refundable. 6.Man-made damage by abuse or wrong operation is not covered by this warranty. 7.No product liability insurance is assumed. 8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ] Customer Services Q: How do I pay for my purchase? A: MY store accepts PayPal, VISA, Master Card, etc. . Q: When will the item be shipped out? A: This item will be shipped with 2 business day once payment completed. Q: Where is my tracking number? A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email. Q: How do I return an item? A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ] Feedback 1. We will leave a feedback once we get your payment. 2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers. 3. If you are satisfied with the product you received, wish you can leave us a feedback. Shop Category Store Home ABS Wheel Speed Sensor AC Compressor AC Compressor Control Valve+A AC Condenser & Radiator ◈ AC Condenser ◈ AC Condenser & Radiator ◈ Radiator Adjustable Control /Camber Arm Air Cleaner Filter Box Air Diesel Heater Air Dryer Air suspension valves solenoid Air suspensions Alternators ATV Brake Caliper ATV Brake Master Cylinder ATV Ignition Switch ATV Rear Wheel Axle Auto parts ◈ Blower Motor ◈ Coilover ◈ complete struts ◈ CV Axle ◈ Fuel Pump Assembly ◈ Ignition Coil ◈ Key Case ◈ Starter ◈ strut/absorber shock ◈ Struts/Absorbers Shocks ◈ Towing Mirrors ◈ Trunk Floor Mats ◈ Window Switch ball joint Ballast module Bed Step Blower Motor & Resistor Brake Oil Hose Brake Pads & Rotors ◈ Brake Pad Sensor ◈ Brake Pads ◈ Brake Rotors ◈ Brake Rotors and Pads Brake System Parts ◈ Brake Calipers ◈ Brake Drums & Brake Shoes ◈ Brake Pads & Brake Shoes Bumper Camshaft & Crankshaft Camshaft Position Sensor Car Antenna Car Carburetor Car Cover Car Seat Cover Car Tools Cargo Cover CDI BOX Clock Spring Coil Springs Consoles & Parts Control Arms & Parts Cooling Fan Cooling Fan Clutch Crankcase Vent Valve Crankshaft Position Sensor CV axle+Brake Pads/Rotors Cylinder Head Gasket Sets Cylinder Piston Gasket Kit Cylinder Piston Kit dash cover Dipstick Door check stop Door handle Door Lock Actuator Driveshaft Electric Water Pump Electrical & Test Equipment Engine Mount Evaporators Fastener Fender Flares fog lights Foot Rest Pedal Front Bumper Lip Fuel Injectors Fuel Pressure Regulator Fuel Tank Pipe Fuel Valve& Petcocks Fuel Vapor Charcoal Canister Fuse Holder Box Glow Plug golf Harmonic Balancer headlight motorcycle Heater Control Valve Heater Cores Height Level Sensor Home & Garden ◈ Portable Fans Horns & Sirens Hot Stapler Hub Caps HVAC Hydraulic Lifter&Roller Lifter idle air control valve Intake Exhaust Valves Intercooler Jack Stands jumper cable Knock Sensor LED headlight Assembly leveling lift kit leveling lift kit+shock struts License Plate Frame lift support Light Bar Mount Bracket Lights ◈ Exterior Lights ◈ Instrument Panel Lights ◈ Interior Lights ◈ Led Headlights ◈ Side/Cab Marker Lights ◈ Special Model Lights ◈ Third Brake Lights Lower Kits & Parts MAP Sensor Mass Air Flow Sensor Mirror Assemblies Motorcycle Brake Clutch Lever Motorcycle Carburetor & Parts Nerf Bars & Running Boards O Ring Off-Road Axles & Half Shafts Oil Catch Can Tank Oil Cooler Oil Fuel Hose Line Oil Pan Oil Pressure Sensor Oil Pump Other Golf Cart Parts Oxygen Sensors Parking sensor Pillar Posts Power Brake Booster Power Steering Pump Pressure Tester Gauge primary drive clutch PTO Clutch Purge Valve Radiator Coolant Tank Radiator Hose Radiator Support Regulator Rectifier Removal Open Tools Rocker Arm Roof rack Rubber Seal Strip Running Board Motor Secondary Air Injection Pump Sensor-8 snorkel air intake Spark Plug Spark Plug Ignition Wire Spindle Splash Guards & Mud Flaps Spoilers & Wings Starter Relay Solenoid Stator Steering Knuckle steering knuckle-7 Steering Rack Steering Shaft Steering U-Joint Steering Wheel Steering Wheel Hub Strut Mount Strut Tie Bar Sun Visor suspension 5 BIN ◈ chenjiao suspension kit ◈ suspension cj ◈ suspension fu ◈ suspension gxy ◈ Suspension Kits Suspension+Strut+Bearing Temperature Sensor Tensioners Thermostat Housing Throttle Body Throttle Position Sensor Timing Belt Kits Timing Chain Kits Tire Pressure Gauge Tire Pressure Sensor Tonneau Cover Transfer Case Shift Motor transmission filter transmission kit trim tilt motor Trunk Mat Turbocharger Valve Cover Variable Timing Solenoid (VVT) vehicle speed sensor water Pump Impeller Water Pumps wheel hub bearing Wheel Hub Bearing Knuckle Wheel Hub Centric Rings Wheel lug nut Wheel Spacers winch Window Regulator window visor Windshield Outer Trim Windshield Wiper Motor Windshields Other New List Item 4Pcs Engine Motor Mount Kit Set For Chevrolet Traverse For GMC Acadia 2009-2015 USD 92.59 6PCS Ignition Coil Fits Chrysler Sebring Concorde Intrepid Dodge Stratus UF199 USD 61.99 Ignition Coil For Nissan Versa 1.6L 2012-2019 Nissan Versa Note 1.6L 2014-2019 USD 14.49 4 PCS Ignition Coils For Chevrolet Equinox GMC Terrain 1.5L 2018 2019 USD 49.99 New Ignition Coil Fits Chrysler Sebring Concorde Intrepid Dodge Stratus UF199 USD 16.39 Hot Item Fuel Pump Assembly for Buick Lesabre Cadillac Deville Park Avenue Pontiac E3518M USD 32.99 2pc 3157 4114 4157 LED DRL Driving Daytime Running Light Bulbs 12SMD 6000K White USD 8.39 Rear Pair Air Suspension Spring Bags For Lincoln Town Car Marquis Crown Victoria USD 62.08 12V Universal Fuel Pump Gas Diesel Inline Low Pressure HEP-02A BHEP-02A USD 12.09 Inline Universal High Pressure Fuel Pump With Installation Kit 0580464070 USD 20.49 Warranty Radiator and Cooling Fan Assembly Kit For 2008 2009 2010 2011-2012 Ford Escape Fitment: 2008-2012 Ford Escape 2009-2011 Mercury Mariner Notes: The radiator cooling fan is an integral part of your car that is responsible for cooling the radiator of your car. The radiator cooling fan does this by either pulling or pushing air into the radiator keeping the radiator temperatures within the safe levels. A damaged radiator cooling fan is a determining factor in preventing your car from overheating. Below are the materials that you need along with the instructions on how to replace a radiator cooling fan. Step 1: Locate the Radiator Cooling Fan Locating the radiator cooling fan is the first step in replacing it. Turn off your car and allow it to cool off. Open the hood of your car and you will be able to see the radiator that is located at the back of the grill at the front portion of your engine compartment. The radiator cooling fan is attached at the back of the radiator through a mounting frame. Under the engine and the radiator is a sticking cylinder that is encased in a small casing. That is the radiator cooling fan motor that you may need to change or repair other than the radiator cooling fan itself. Step 2: Disconnect the Power Supply On the fan motor is an electric cable running towards the engine. Find the connector of the wires from your engine and from your radiator fan motor and disconnect it. Using two masking tapes with different colors, note the connection of the wires so that you will not have a hard time reconnecting the wires later. Step 3: Remove the Fan Housing Using a crescent wrench, remove the four screws located at each corner of the fan housing. Remove the fasteners at the sides of the fan housing as well. A radiator cooling fan housing is relatively large and you may need to remove all the obstructions like hoses and wirings so that you can extract the fan housing off your car hood. Hold the housing firmly and lift it off your engine compartment. Be careful in removing the fan housing to avoid damaging it. Place the fan housing on a clutter-free working table. Step 4: Remove the Radiator Cooling Fan and the Fan Motor The fan blade is either pinned or screwed to a shaft. With a screwdriver, loosen the fan blade and slide if off its shaft. You may need to remove a keeper that prevents the fan blades from moving up in the shaft up and down. As to the fan motor itself, remove it from the fan housing using a screwdriver. Step 5: Attach the Replacement Radiator Cooling Fan and Fan Motor Install the new fan motor into the fan housing. Slide your replacement radiator cooling fan into the shaft, insert the keeper and secure the new cooling fan and keeper into place. Return the fan housing back into its proper place and secure the screws and the fasteners. Reattach the hoses and wires you removed in step 3. Connect the fan motor into the car electrical system using the electrical tape guide you made in step 54. You just learned how to replace your radiator cooling fan as well as your radiator cooling fan motor. Information About AC Condenser 1.Such condensers typically also use a fan to force air through the heat sink and away from the tropics. Refrigeration principle of the general refrigerator The function of the compressor is to compress the steam with lower pressure into steam with higher pressure, so that the volume of the steam is reduced and the pressure is increased. 2.The compressor draws in the lower pressure working fluid vapor from the evaporator, causes the pressure to rise, and then sends it to the condenser, which is condensed into a higher pressure liquid in the condenser, and is throttled after the throttling valve becomes a pressure. After the low liquid is sent to the evaporator, it absorbs heat in the evaporator and evaporates to become a lower pressure steam, thereby completing the refrigeration cycle. Shipping WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. 2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days. 3.Local pick up is not available. 4. International Buyers C Please Note: a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ] Payment 1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc.. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns 1.All of our brand new items come with a 60-Days money-back guarantee. 2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding. 3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. 4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. 5.Shipping& handling cost are not refundable. 6.Man-made damage by abuse or wrong operation is not covered by this warranty. 7.No product liability insurance is assumed. 8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ] Customer Services Q: How do I pay for my purchase? A: MY store accepts PayPal, VISA, Master Card, etc. . Q: When will the item be shipped out? A: This item will be shipped with 2 business day once payment completed. Q: Where is my tracking number? A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email. Q: How do I return an item? A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ] Feedback 1. We will leave a feedback once we get your payment. 2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers. 3. If you are satisfied with the product you received, wish you can leave us a feedback. Copyright of SCITOO-AutoParts . All rights reserved.